Introduction
This troubleshooting guide helps you resolve the most common issues with your OREI UHD-EX165H-K HDMI Extender. It covers no signal, decode errors, resolution limits, latency, IR control problems, and compatibility questions so you can quickly identify the cause and restore video performance.
Issue description
The OREI UHD-EX165H-K is a 4K@60Hz HDMI extender that sends an HDMI signal over a single CAT6 cable with IR control and HDMI loop-out. You may experience issues such as no video on the remote display, a Decode disabled message, reduced resolution, lag when switching content, IR control failures, or compatibility limitations with certain source devices and PC resolutions.
Signs
- Your remote display shows no signal even though both extender units have their LEDs on.
- Your transmitter shows solid green with blinking orange, while your receiver shows solid green with no orange LED.
- Your screen displays Decode disabled when you use an NVR or camera system as the source.
- Your video is limited to 1080p@60Hz or 4K@30Hz instead of 4K@60Hz.
- Your 4K@60Hz resolution worked previously but has now dropped to a lower resolution.
- You notice lag when switching content, such as on a Roku device.
- Your IR remote control does not work as expected.
Basic troubleshooting steps
Checklist:
- Verify that all HDMI cables are securely connected at the source, transmitter, receiver, and display.
- Check the CAT cable type and make sure you are using a round, shielded CAT6 cable wired to the 568B standard with solid bare copper conductors.
- If possible, test with a shorter CAT cable to rule out cable length or signal quality issues.
- Power cycle both units by disconnecting their power supplies, waiting a few seconds, and reconnecting them.
- Connect a display directly to the HDMI loop-out on the transmitter to confirm that your source device is outputting video correctly.
- Try a different source device to determine whether the issue is caused by your source rather than the extender.
- Check the EDID DIP switch settings on the transmitter before changing advanced settings.
- For IR issues, verify the IR blaster and receiver connections and placement.
Advanced troubleshooting steps
Step 1: Check the CAT cable and link status
If your transmitter shows solid green with blinking orange and your receiver shows solid green with no orange LED, the link is not established. Replace your CAT cable with a round, shielded CAT6 cable wired to the 568B standard and made with solid bare copper conductors. If possible, test with a shorter cable to confirm whether the issue is related to cable quality or length.
Step 2: Verify the source and HDMI path
Connect a display to the HDMI loop-out on your transmitter to verify that your source is working. If you still do not get video, try a different source device and confirm that the HDMI cable between your source and transmitter is working properly. This helps isolate whether the problem is with your source, the transmitter, or the remote link.
Step 3: Adjust EDID settings
Use the EDID DIP switches on your transmitter to test compatibility. Start with TX EDID mode, which copies EDID from the transmitter side. Power cycle both units after changing the setting. If TX mode does not resolve the issue, switch to RX EDID mode, which reads EDID from the display connected to your receiver, then power cycle both units again.
Step 4: Resolve resolution and compatibility limits
The UHD-EX165H-K supports up to 4K@60Hz 4:4:4 over CAT6 up to 115 ft (35 m). Although the product is rated for 165 ft, 4K@60Hz performance is only achievable up to 115 ft. If you need 4K@60Hz, reduce your CAT cable length and use shielded CAT6.
The unit does not support 2560x1440 natively. If your PC requires 1440p or higher refresh rates, an HDBaseT extender such as the UHD-EX115UHD-K or UHD-EXB400R-K is recommended.
Step 5: Address decode disabled or firmware-related issues
If you see a Decode disabled message, especially when using an NVR or camera system, confirm that your source is compatible with the extender. Try a different shielded CAT cable, test the EDID switch settings, and power cycle both units. A firmware update may be available through the service port if the issue persists.
Step 6: Test for intermittent 4K@60Hz loss
If your 4K@60Hz resolution worked previously but now drops to 4K@30Hz, replace your CAT cable with a round, shielded, solid-copper CAT6 cable and test again.
Then disconnect your receiver and CAT cable and test the transmitter using the HDMI loop-out only. If the issue remains, try a different source device. If none of these steps restore performance, an RMA or warranty replacement may be required.
Step 7: Reduce latency and improve switching performance
Some latency is normal and should be minimal or unnoticeable. If switching content on a device such as Roku feels delayed, upgrade from CAT5 to CAT6 and use a round, shielded CAT6 cable wired to the 568B standard. A firmware update may also be available if the issue continues.
Step 8: Troubleshoot IR control
If your IR remote control is not working, confirm that your IR blaster and IR receiver are connected correctly and positioned properly. Make sure your IR receiver has a clear path to your remote control and that the blaster is aimed at your source device's IR window.
Contact support
If the issue is not resolved after completing the steps above, contact OREI support for further assistance.
Email: info@orei.com
Phone: +1 877-290-5530
Support hours: 9 AM to 5 PM CST, Monday through Friday
Disclaimer
This troubleshooting guide is provided for informational purposes only. Results may vary depending on your source device, display, cabling, and installation environment. If you are unsure about any step, or if your product continues to malfunction after troubleshooting, contact OREI support or seek assistance from a qualified AV professional.
Comments
0 comments
Please sign in to leave a comment.