Introduction
This troubleshooting guide helps you resolve common issues with the OREI HDA-927 4K eARC HDMI Audio Extractor. The HDA-927 is designed to extract audio from an HDMI source or from a TV's ARC/eARC port and send it to a legacy AVR with a standard HDMI input that does not support ARC or eARC. It also passes video and audio to your TV through HDMI OUT 1.
Use this guide if you are having trouble with audio output, video pass-through, eARC detection, EDID settings, or compatibility with your TV or AVR.
Issue description
The HDA-927 is intended for setups where you want to send audio from a TV's ARC/eARC port or from an external HDMI source to a legacy AVR that only has standard HDMI inputs. It supports 4K at 60Hz and is not designed for 4K at 120Hz gaming systems. It also does not support CEC pass-through on the HDMI AUDIO OUT 2 port and is not intended for use with ARC/eARC soundbars.
Signs
- No audio from HDMI AUDIO OUT 2
- eARC LED is blinking or will not stay on
- No video on the TV or signal not detected
- AVR receives no audio or the wrong audio format
- Volume control or CEC commands do not pass through
- Audio works from one source but not when switching between TV apps and HDMI devices
- The unit powers off intermittently or LEDs go dark
Basic troubleshooting steps
- Confirm the HDMI source, TV, and AVR are all powered on.
- Verify the HDMI source is connected to HDMI IN, the TV is connected to HDMI OUT 1, and the AVR is connected to HDMI AUDIO OUT 2.
- Use certified high-speed HDMI cables and keep cable lengths as short as possible for testing.
- Check that ARC/eARC is enabled on the TV when using TV apps or TV audio.
- If you are using a non-ARC or non-eARC TV, press the eARC button to turn off the eARC LED so the unit extracts audio from the HDMI source instead.
- For TV app audio, make sure the TV is connected to HDMI OUT 1 and the TV's audio output is set to ARC/eARC.
- Power cycle the TV, AVR, source device, and HDA-927 by unplugging them for 30 seconds, then reconnecting them in order.
- Check the EDID setting and audio format on the HDA-927 if audio is missing or incompatible.
Advanced troubleshooting steps
1. No audio output or audio not working
If there is no audio from HDMI AUDIO OUT 2 or no sound from the TV, check the current signal path first. The HDA-927 can extract audio either from the HDMI source or from the TV's ARC/eARC port, but only one audio path may be active at a time depending on the mode selected.
- Confirm the AVR is connected to HDMI AUDIO OUT 2 and the TV is connected to HDMI OUT 1.
- If you are using TV apps such as Netflix, make sure ARC/eARC is enabled on the TV and the eARC LED is on.
- If you are using an external HDMI source, press the eARC button if needed so the unit switches away from TV ARC/eARC audio and extracts audio from the HDMI source.
- Test with a different HDMI source and a different HDMI cable to rule out a source or cable issue.
- Set the AVR input to the correct HDMI input and confirm the AVR volume is not muted.
2. eARC LED blinking or eARC not establishing
A blinking eARC LED usually indicates the unit is trying to establish an ARC/eARC handshake with the TV but is not completing it successfully.
- Confirm the TV supports ARC or eARC on the HDMI port connected to HDMI OUT 1.
- Enable HDMI-CEC and ARC/eARC in the TV audio settings if required by the TV manufacturer.
- Power off the TV and the HDA-927, then reconnect and power them on again.
- If you are using a non-ARC/non-eARC TV, press the eARC button to turn off the eARC LED. The unit should then extract audio from the HDMI source instead of waiting for TV ARC/eARC.
- Try a different HDMI port on the TV if the TV has multiple ports with ARC/eARC support.
3. No video output or signal not detected
If the TV shows no picture, the issue is usually related to cable quality, incorrect connections, or an unsupported video format.
- Make sure the source device is connected to HDMI IN and the TV is connected to HDMI OUT 1.
- Confirm the source is outputting a supported resolution and refresh rate. The HDA-927 supports up to 4K at 60Hz only.
- If you are using a 4K at 120Hz console or PC, set the source to 4K at 60Hz or lower for testing.
- Use a certified HDMI cable and test with a shorter cable if possible.
- Bypass the HDA-927 temporarily by connecting the source directly to the TV to confirm the source and TV are working.
4. AVR not receiving audio / wrong audio format
If the AVR is connected but receives no sound, or if it receives a format it cannot decode, check the TV audio format, EDID setting, and the source output format.
- Verify the AVR is connected to HDMI AUDIO OUT 2 and is set to the correct input.
- Check whether the source is sending PCM, Dolby Digital, Dolby Digital Plus, or another format supported by your AVR.
- If your AVR is older, set the source or TV audio output to Dolby Digital 5.1 or PCM as needed.
- Review the HDA-927 EDID setting and choose the option that matches your display and AVR capabilities.
- Remember that the HDA-927 does not support eARC/ARC soundbars. If your audio device is a soundbar that requires ARC/eARC, use the HDA-929 instead.
5. Unit not powering on or LEDs going dark
If the LEDs turn off or the unit appears dead, the issue is often related to power delivery or a loose connection.
- Use the included power adapter or a replacement adapter with the correct voltage and current rating.
- Make sure the power cable is fully inserted into the unit and the wall outlet.
- Try a different wall outlet or power strip.
- Disconnect all HDMI cables and reconnect them one at a time to see whether a connected device is causing power instability.
- If the unit still does not power on, contact support for further testing.
6. Intermittent connection or cycling on and off
If the picture or audio drops in and out, the most common causes are cable quality, bandwidth limitations, or handshake instability between devices.
- Replace long or low-quality HDMI cables with certified high-speed cables.
- Reduce the source output to 4K at 60Hz, especially if the source is set to 4K at 120Hz or another unsupported mode.
- Remove other HDMI devices or splitters from the signal path during testing.
- Power cycle the source, TV, AVR, and HDA-927 in that order.
- If the issue happens only with TV apps, recheck ARC/eARC settings on the TV.
7. CEC not working / volume control not passing through
The HDA-927 does not support CEC pass-through on the HDMI AUDIO OUT 2 port. This means volume control and other CEC commands may not pass to the AVR through the audio output connection.
- Do not expect CEC volume control to work through HDMI AUDIO OUT 2.
- Use the AVR remote, a universal remote, or the TV's own audio control methods if supported by your setup.
- Confirm CEC is enabled on the TV if you are using TV app audio, but note that CEC behavior varies by TV brand and model.
- If you need full CEC-based soundbar control, the HDA-927 is not the correct product for that application.
8. EDID settings confusion
EDID settings determine what audio and video formats the source device sees as supported. Incorrect EDID settings can cause no audio, no video, or reduced audio format options.
- Use the EDID setting that matches the capabilities of your TV and AVR.
- If you want simple compatibility with a legacy AVR, try PCM or Dolby Digital 5.1 output first.
- If the source is not showing the expected audio options, power cycle the source after changing EDID so it can read the new settings.
- If you are unsure which EDID mode to use, test one setting at a time and note the result.
9. Non-eARC TV compatibility
The HDA-927 can work with non-ARC and non-eARC TVs for HDMI source audio extraction, but TV app audio requires ARC or eARC support on the TV. If the TV does not support ARC/eARC, the unit cannot pull audio from TV apps through the TV's return audio path.
- For non-ARC/non-eARC TVs, connect the HDMI source to HDMI IN and use the HDA-927 to extract audio from the source directly.
- Press the eARC button to turn off the eARC LED so the unit does not wait for ARC/eARC from the TV.
- Do not expect audio from TV apps on a TV without ARC/eARC support.
- If your setup requires audio from TV apps, use a TV with ARC/eARC or connect the source device directly to the HDA-927 and TV.
10. Audio format support questions
The HDA-927 supports audio extraction from HDMI sources and from TV ARC/eARC, but the final audio format depends on the source, the TV, and the AVR. Use the scenarios below to identify the correct setup.
- If you are using TV apps like Netflix, connect the TV to HDMI OUT 1, enable ARC/eARC on the TV, and use the eARC button as needed to select TV audio.
- If you are using a legacy AVR with standard HDMI input only, expect compatibility with common formats such as PCM and Dolby Digital 5.1, depending on the TV and source settings.
- If you are using an ARC-only TV, audio may be limited to Dolby Digital 5.1 and may not support Dolby Atmos.
- If you are using an eARC soundbar, the HDA-927 is not supported. Use the HDA-929 instead.
- If you are gaming at 4K at 120Hz, the HDA-927 is not the correct model. It is limited to 4K at 60Hz.
Contact support
- Your order number or proof of purchase
- The model number: HDA-927
- A description of the issue and when it started
- The TV model, AVR model, and source device model
- The current cable types and lengths used in the setup
- The EDID setting and whether the eARC LED is on or blinking
Support hours: Monday to Friday, 9:00 AM to 5:00 PM EST
Email: info@orei.com
Phone: +1 877-290-5530
Disclaimer
This guide is provided for general troubleshooting only. Results may vary depending on your TV, AVR, source device, HDMI cables, and system configuration. The HDA-927 is limited to 4K at 60Hz, does not support CEC pass-through on the HDMI AUDIO OUT 2 port, and is not intended for ARC/eARC soundbars. If your setup requires those features, use the appropriate OREI product or contact support for guidance.
Comments
0 comments
Please sign in to leave a comment.