Introduction
This troubleshooting guide is designed to help you resolve common issues with your OREI HD-EXM330-K HDMI Over IP Extender Kit. This 1080p extender uses CAT5e or CAT6 cable to extend HDMI signals up to 330 feet and supports one transmitter connected to multiple receivers through a dedicated network switch. Follow the steps below to identify the cause of the issue and restore normal operation.
Issue description
You may experience issues with your HD-EXM330-K, such as no signal, intermittent video, audio limitations, overheating, loop-out performance concerns, resolution incompatibility, or network switch-related problems. This guide covers the most common symptoms and provides practical troubleshooting steps for your transmitter, receiver, cabling, display, and network switch setup.
Signs
- Your power LEDs are solid, but the link LEDs are blinking and no image appears on your receiver display.
- Your system works when the transmitter and receiver are connected directly but fails when routed through a network switch.
- Your unit randomly shows no input, loses signal, or shuts down intermittently after working normally.
- You do not get audio, especially when attempting to use ARC.
- Your transmitter feels unusually hot during continuous use.
- Your loop-out display shows latency or performance issues.
- Your source device is set to 1080i or another unsupported resolution.
Basic troubleshooting steps
Use this checklist to rule out the most common causes before moving to advanced troubleshooting.
- Check the LED status on both your transmitter and receiver.
- Test the HDMI loop-out on your transmitter by connecting it directly to a display.
- Swap your CAT cable and confirm that you are using a flat, straight CAT5e or CAT6 cable, not a round or shielded cable.
- Reduce your source resolution to 1080p progressive. The unit does not support 1080i.
- Try a different source device to rule out a source compatibility issue.
- Verify HDCP compatibility. Some NVR and DVR sources may cause HDCP-related issues.
- Confirm that your receiver is being used with a compatible transmitter hardware version.
- If you are using a network switch, make sure it is dedicated to your extender system and not shared with computers, printers, POS systems, or other network devices.
Advanced troubleshooting steps
Step 1: Verify the signal path from source to display
Connect your source directly to the transmitter and connect the transmitter loop-out directly to a display. If the loop-out works, your source and transmitter are likely functioning correctly. If the loop-out does not work, test with another source device and confirm that your source is outputting a supported progressive resolution.
Step 2: Check the CAT cable and link status
Inspect the CAT ports on both units. The green and yellow port LEDs should indicate active communication. Replace your cable if the link LEDs blink continuously, if the signal drops out, or if the cable is round, shielded, damaged, or not terminated correctly. Use a flat, straight CAT5e or CAT6 cable for best results.
Step 3: Test the system with a dedicated network switch
If your extender works when connected directly but fails through a switch, replace the switch with a dedicated network switch used only for your HD-EXM330-K system. Do not share the switch with computers, printers, POS systems, or unrelated network traffic, as this can interfere with signal transmission and affect other devices on your network.
Step 4: Confirm resolution and format compatibility
Set your source to 1080p or another supported progressive resolution. The HD-EXM330-K does not support interlaced resolutions such as 1080i. If you are using a 1920x1200 display, verify that your display supports that resolution before testing.
Step 5: Review HDCP and source compatibility
If your source is an NVR, DVR, or another protected device, HDCP may prevent proper video output. Test with a standard HDMI source, such as a media player, laptop, or streaming device, to confirm whether the issue is source-related. Video capture cards are not supported due to HDCP.
Step 6: Address intermittent loss or random shutdowns
If your unit works for a while and then shows no input, check for heat buildup, poor ventilation, cable crossings, nearby electrical devices, or other environmental interference. Power cycle your system in the correct order: turn off your source, transmitter, receiver, and switch (if used), then power them back on one at a time.
Step 7: Check ventilation and device temperature
Your transmitter may become warm during normal continuous use. Place it in a cool, well-ventilated area and avoid stacking it near heat-producing equipment. If your transmitter becomes too hot to handle, stop using it and contact support, as the unit may be defective.
Step 8: Verify loop-out behavior
The HDMI loop-out on your transmitter is a pass-through and should not add noticeable latency. If you experience severe delay or performance loss on the loop-out output, test with another source and display. Persistent latency may indicate a faulty transmitter.
Step 9: Confirm audio expectations
The HD-EXM330-K does not support ARC or CEC. If you are trying to send audio back over ARC, this extender will not provide that function. Use an ARC-specific solution instead. Your unit does support IR control.
Step 10: Verify IP and RTSP details
If you are accessing your extender over IP or RTSP, confirm the default addresses: transmitter 192.168.1.238 and receiver 192.168.1.239. Your device provides an RTSP video stream, but audio may not be available through RTSP.
Contact support
If the issue continues after completing the steps above, contact OREI support with the following information: your model number, transmitter and receiver hardware versions, source device model, display model, cable type and length, switch model (if used), LED status, and a description of the symptoms. This information will help us diagnose your issue faster.
Disclaimer
This guide is provided for general troubleshooting only. Results may vary depending on your source devices, displays, cabling, network equipment, and installation environment. If your unit becomes excessively hot, continues to fail after troubleshooting, or appears defective, discontinue use and contact OREI support for assistance.
Comments
0 comments
Please sign in to leave a comment.