Introduction
This guide helps you troubleshoot common issues with your OREI UHD-404 4x4 HDMI Matrix Switch. The UHD-404 is an 18Gbps HDMI matrix designed to route one of four HDMI sources to any of four displays independently, with support for 4K at 60Hz, HDR, Dolby Vision, HDCP 2.2, per-output downscaling, ARC on Output A, and audio extraction. Use this article to identify the most common causes of video, audio, EDID, CEC, and power-related issues and to determine when your unit may need service or replacement.
Issue description
You may experience issues such as one or more displays not showing video, a specific output stopping working, audio not passing as expected, your monitor not reaching its native resolution, or the front-panel LEDs behaving unexpectedly. Some issues may be caused by routing, cabling, EDID settings, or source and display compatibility. In other cases, the symptoms may indicate a hardware or power failure.
Signs
- No video on one or more outputs, while your other outputs work normally
- Only one output LED blinks red, or the front-left LED stays on with a blinking red light
- An output works intermittently or fails completely after previously working
- Your display shows a lower-than-expected resolution, especially on ultrawide or non-standard monitors
- Audio does not play through your HDMI monitor or through the matrix audio outputs
- CEC commands from your source devices do not control your TV
- Security camera, NVR, or DVR video does not pass through correctly
Basic troubleshooting steps
Before moving to advanced steps, check the most common causes of signal and compatibility issues.
- Confirm that the correct input is assigned to the affected output using the OUT buttons or the remote control.
- Verify that your source device is powered on and sending a signal.
- Check that your display is set to the correct HDMI input.
- Swap HDMI cables between outputs to determine whether the problem follows the cable or stays with the port.
- Connect your affected display to a different output port to isolate a possible port issue.
- Power cycle your source devices, displays, and matrix for at least 2 minutes.
- Connect your display directly to the source to confirm that the display and source work together without the matrix.
- Check the EDID DIP switch setting and confirm that it matches the resolution and audio format you need.
- Use a short, high-quality HDMI 2.0 or 18Gbps cable for testing.
Advanced troubleshooting steps
Step 1: Verify output routing and input selection
Each output on your UHD-404 can route any input independently. If your display is blank, confirm that the intended input is assigned to that output. Use the front-panel OUT buttons or the remote to reassign the source, then test again.
Step 2: Test the cable and display path
Swap the HDMI cable from a working output to the affected output. If the issue moves with the cable, replace the cable. If the issue stays with the same output, test your display on another output port. This helps isolate whether the problem is with the cable, display, or matrix output.
Step 3: Check EDID DIP switch settings
Use the EDID DIP switches to match your display and source requirements. Common settings include 0000 for 1080p stereo, 0001 for 4K at 30Hz, 0010 for 4K at 60Hz, and 0011 for Copy OUT1 EDID. For ultrawide or mixed-resolution systems, Copy OUT1 EDID often provides the best compatibility. If your display is not reaching its native resolution, test with 0011 and compare the results.
Step 4: Reduce the signal load for testing
Disconnect all but one source and one display, then test the affected output by itself. This simplifies troubleshooting and helps determine whether another source, display, or cable in your system is affecting the signal.
Step 5: Test downscaling on the affected output
If your display cannot handle the incoming resolution, enable downscaling for that output by holding the OUT button for 3 seconds or pressing the SD button to toggle downscaling. Test both states to see whether your display becomes stable with a lower resolution.
Step 6: Check audio routing and extraction
The Optical A output follows Output A, and Optical B follows Output B. The Stereo A and Stereo B outputs are analog outputs and are limited to PCM 2.0 stereo. If you are connecting an amplifier, use Toslink for optical input or a 3.5 mm cable for analog input. Your unit does not have an optical input, only optical outputs.
Step 7: Confirm audio settings on your source device
If audio does not play through your HDMI monitor, check your computer or source device audio settings. In Windows, confirm that the correct monitor is selected as the audio output device and that HDMI audio is enabled on your laptop or source device.
Step 8: Understand HDCP limitations
Some NVR, DVR, and security camera systems may not work through your matrix because of HDCP incompatibility. To verify whether this is the cause, test your matrix with a standard HDMI source such as a media player, game console, or laptop.
Step 9: Confirm CEC expectations
Your UHD-404 does not support HDMI-CEC. CEC commands from devices such as Apple TV or Nintendo Switch will not pass through to your TV, and there is no setting to enable CEC passthrough.
Step 10: Inspect power and front-panel LED behavior
If only the left-most front LED is on with a blinking red light, or if your output LEDs behave unpredictably after several days, your unit may have a power or hardware fault. Try a full power cycle, confirm that the power adapter is properly connected, and retest. If the behavior continues, your unit may be defective.
Step 11: Perform a factory reset and retest failed outputs
If one or more outputs stop working, power cycle your unit for 5 minutes, connect a known working source and display directly to the affected output, set EDID to 1080p stereo using 0000, and perform a factory reset if available. If the output still does not work after these steps, your unit is likely defective.
Step 12: Update firmware through the SERVICE Micro USB port
Firmware upgrades are available through the SERVICE Micro USB port. If our support team provides a firmware file, follow the supplied instructions carefully and complete the update before retesting your system.
Contact support
Contact OREI support if the issue continues after troubleshooting or if your unit appears to be defective. Please include the following details when you reach out:
- A photo or short video of your unit's front panel and LED behavior
- The purchase date and warranty status
- Your source device model and display model
- The EDID DIP switch setting currently in use
- A description of your cables and connection layout
Disclaimer
Troubleshooting results can vary depending on your source device, display, cable quality, EDID configuration, and system design. The UHD-404 does not support HDMI-CEC passthrough, and some HDCP-protected or non-standard resolution devices may not be compatible in every setup. If you are unsure about a setting or a firmware update, contact our support team before making changes.
Comments
0 comments
Please sign in to leave a comment.