What Is the UHD-FO10-KVM?
The OREI UHD-FO10-KVM is a 4K@60Hz HDMI over Fiber-Optic Extender with HDMI loop output and USB keyboard/mouse transmission.
It is designed to extend uncompressed HDMI signals up to 10km over single-mode fiber cable. It supports video resolutions up to 4K@60Hz 4:4:4, HDMI 2.0b, HDCP 2.2, 18Gbps bandwidth, HDR10, HDR10+, Dolby Vision, HLG, 3D video, and wide HDMI audio format support.
The system includes a Transmitter and Receiver. The Transmitter connects to the HDMI source and sends the signal through fiber to the Receiver. The Receiver connects to the remote HDMI display and also provides audio de-embedding and USB keyboard/mouse control.
The Transmitter includes an HDMI loop output for connecting a local monitor. The Receiver includes a 3.5mm audio output and two USB Type-A ports for keyboard and mouse. The USB function supports USB 1.1 HID devices only, such as a keyboard and mouse.
The UHD-FO10-KVM is useful for commercial AV installations, control rooms, command centers, security monitoring, digital signage, classrooms, conference rooms, high-end AV systems, and long-distance HDMI installations where a source computer needs to be controlled from the display side.
IMPORTANT — UHD-FO10-KVM Is an HDMI over Fiber Extender with KVM
The UHD-FO10-KVM extends HDMI and USB keyboard/mouse control over fiber.
| Function | Support |
| HDMI over fiber extension | Supported |
| Transmitter and Receiver kit | Supported |
| Single-mode fiber transmission | Supported |
| Up to 10km transmission distance | Supported |
| HDMI loop output on Transmitter | Supported |
| Audio de-embedding on Receiver | Supported |
| USB keyboard/mouse control | Supported |
| USB 1.1 HID devices | Supported |
| USB storage devices | Not supported |
| HDMI switching | Not supported |
| HDMI matrix routing | Not supported |
This product is not an HDMI switch, splitter, or matrix.
It is designed to extend one HDMI source to one remote HDMI display over fiber while also allowing keyboard and mouse control from the Receiver side.
IMPORTANT — Transmission Distance Depends on Fiber Type
The UHD-FO10-KVM supports long-distance transmission over fiber cable.
| Fiber Type | Maximum Distance |
| Single-mode fiber | Up to 10km |
| Multi-mode OM4 fiber | Up to 300m / 1000ft |
For the longest and most stable installation, use single-mode fiber cable.
Multi-mode OM4 fiber can be used, but the transmission distance is reduced to 300m / 1000ft.
IMPORTANT — Supports 4K@60Hz 4:4:4
The UHD-FO10-KVM supports high-quality 4K HDMI video.
| Video Feature | Support |
| Maximum resolution | 4K@60Hz 4:4:4 |
| HDMI compliance | HDMI 2.0b |
| HDCP compliance | HDCP 2.2 |
| Video bandwidth | 18Gbps |
| 4096x2160p60 / p50 | Supported |
| 3840x2160p60 / p50 / p30 / p25 | Supported |
| 1920x1080p60 / p50 | Supported |
| 1920x1200p60RB | Supported |
| 1360x768p60 | Supported |
| 1280x800p60 | Supported |
| 1280x720p60 / p50 | Supported |
| 1024x768p60 | Supported |
To get 4K@60Hz 4:4:4, the HDMI source, display, HDMI cables, fiber cable, and SFP modules must all support the required signal.
IMPORTANT — HDR10, HDR10+, Dolby Vision, and HLG Are Supported
The UHD-FO10-KVM supports multiple HDR formats.
| HDR Format | Support |
| HDR10 | Supported |
| HDR10+ | Supported |
| Dolby Vision | Supported |
| HLG | Supported |
For HDR to work, the HDMI source, display, HDMI cables, and fiber extender setup must all support the selected HDR format.
IMPORTANT — HDMI Loop Output Is Supported on the Transmitter
The Transmitter includes an HDMI loop output.
| Port | Function |
| HDMI IN on Transmitter | Connect HDMI source device |
| HDMI OUT on Transmitter | Connect local HDMI monitor |
| HDMI OUT on Receiver | Connect remote HDMI display |
The HDMI loop output allows a local display to be connected near the source device.
This is useful for local monitoring in AV racks, control rooms, classrooms, conference systems, and equipment rooms.
IMPORTANT — USB Keyboard and Mouse Transmission Is Supported
The UHD-FO10-KVM supports USB 1.1 keyboard and mouse transmission.
| USB Feature | Support |
| USB 1.1 HID keyboard | Supported |
| USB 1.1 HID mouse | Supported |
| USB control from Receiver side | Supported |
| USB HOST port on Transmitter | Supported |
| Two USB Device ports on Receiver | Supported |
| USB storage devices | Not supported |
| Printers / webcams / scanners | Not supported |
This model supports USB HID keyboard and mouse control only.
It does not support USB flash drives, external hard drives, printers, webcams, or other USB peripherals.
IMPORTANT — USB Is for KVM Control Only
The USB function is intended for remote control of a source computer.
| Connection | Function |
| Transmitter USB HOST | Connect to the source PC or laptop using USB Type-B |
| Receiver K&M ports | Connect keyboard and mouse |
| Supported USB type | USB 1.1 HID |
| Unsupported USB devices | Storage and other non-HID peripherals |
Use the included USB Type-A to Type-B cable to connect the Transmitter to the host computer.
Connect the keyboard and mouse to the Receiver’s USB Type-A K&M ports.
IMPORTANT — Audio De-Embedding Is Supported on the Receiver
The Receiver includes a 3.5mm AUDIO OUT port.
| Audio Feature | Support |
| Audio de-embedding | Supported |
| Audio output location | Receiver side |
| Audio connector | 3.5mm stereo audio jack |
| Compatible devices | Headphones, soundbar, speakers, amplifier |
Use the Receiver AUDIO OUT port when audio needs to be sent to a local audio device near the display.
For best compatibility with analog audio output, use PCM stereo audio from the HDMI source.
IMPORTANT — Wide HDMI Audio Format Support
The UHD-FO10-KVM supports many HDMI audio formats.
| HDMI Audio Format | Support |
| LPCM 2CH | Supported |
| LPCM 5.1CH | Supported |
| LPCM 7.1CH | Supported |
| Dolby Digital / Plus / EX | Supported |
| Dolby TrueHD | Supported |
| DTS | Supported |
| DTS-EX | Supported |
| DTS-96/24 | Supported |
| DTS High Res | Supported |
| DTS-HD Master Audio | Supported |
| DSD | Supported |
HDMI audio can pass through the extender.
For the Receiver’s 3.5mm audio output, PCM stereo is recommended for best compatibility.
IMPORTANT — Automatic EDID Management Is Supported
The UHD-FO10-KVM uses automatic EDID management.
| Display Connection | EDID Behavior |
| Both Transmitter loop display and Receiver display connected | System compares both display EDIDs and uses the lower capability |
| Only one display connected | System uses that display’s EDID |
This helps maintain stable signal handshakes when two displays with different capabilities are connected.
For example, if a 4K display is connected at one output and a lower-resolution display is connected at the other output, the system may choose the lower display capability to keep both outputs compatible.
IMPORTANT — 10G SFP+ Fiber Module Is Used
The UHD-FO10-KVM uses a 10G SFP+ fiber optic module.
| Fiber Feature | Support |
| Fiber optic module | 10G SFP+ module |
| Fiber connector | LC female |
| Single-mode fiber | Supported up to 10km |
| Multi-mode OM4 fiber | Supported up to 300m |
Make sure the fiber cable is connected correctly between the Transmitter LC FIBER OUT and Receiver LC FIBER IN.
IMPORTANT — External Power Is Required on Both Units
The UHD-FO10-KVM package includes two power adapters.
| Power Feature | Specification |
| Transmitter power adapter | DC 5V/2A |
| Receiver power adapter | DC 5V/2A |
| Power adapters included | 2 |
| Transmitter power consumption | 3.85W max |
| Receiver power consumption | 3.3W max |
Unlike PoC models, this unit lists separate power adapters for both Transmitter and Receiver.
Connect power to both units for normal operation.
Ports and Panel Layout
Transmitter Panel
| Port / Indicator | Function |
| POWER LED | Red LED lights when the Transmitter is powered on |
| LINK LED | Green LED lights when the Transmitter and Receiver have a normal optical fiber connection |
| IN LED | Green LED lights when a source signal is detected on HDMI IN |
| OUT LED | Green LED lights when a display is connected to HDMI OUT |
| SERVICE | USB-C firmware update port |
| LC FIBER OUT | Connect single-mode or multi-mode fiber cable to the Receiver |
| HDMI OUT | Connect local display such as TV or monitor |
| HDMI IN | Connect HDMI source such as DVD player, streaming device, PC, or laptop |
| USB HOST | Connect a PC or laptop through USB |
| DC 5V | Connect included power adapter |
Receiver Panel
| Port / Indicator | Function |
| POWER LED | Red LED lights when the Receiver is powered on |
| LINK LED | Green LED lights when the Transmitter and Receiver have a normal optical fiber connection |
| OUT LED | Green LED lights when a display is connected to HDMI OUT |
| SERVICE | USB-C firmware update port |
| LC FIBER IN | Connect fiber cable from the Transmitter |
| HDMI OUT | Connect remote display such as TV or monitor |
| AUDIO OUT | Connect audio device such as headphones, soundbar, speakers, or amplifier |
| K&M | Connect USB keyboard and mouse |
| DC 5V | Connect included power adapter |
Understanding the LED Indicators
| Indicator | Unit | Status | Meaning |
| POWER LED | Transmitter / Receiver | Red on | Unit is powered on |
| LINK LED | Transmitter / Receiver | Green on | Normal optical fiber signal connection between Transmitter and Receiver |
| IN LED | Transmitter | Green on | HDMI source signal is detected on HDMI IN |
| OUT LED | Transmitter | Green on | Display is connected to Transmitter HDMI OUT |
| OUT LED | Receiver | Green on | Display is connected to Receiver HDMI OUT |
Use these LEDs first when troubleshooting power, fiber link, HDMI input, HDMI loop output, or remote HDMI output.
Step-by-Step Setup
- Place the Transmitter near the HDMI source device.
- Place the Receiver near the remote HDMI display.
- Connect the HDMI source to the HDMI IN port on the Transmitter.
Examples include a PC, laptop, streaming device, Blu-ray player, DVD player, game console, cable box, media player, or HDMI matrix output.
- If local monitoring is needed, connect a monitor or TV to the HDMI OUT port on the Transmitter.
- Connect the remote monitor, TV, or projector to the HDMI OUT port on the Receiver.
- Connect the fiber optic cable between the Transmitter LC FIBER OUT and Receiver LC FIBER IN.
- If using keyboard and mouse control, connect the source PC or laptop to the Transmitter USB HOST port using the included USB Type-A to Type-B cable.
- Connect a USB keyboard and mouse to the Receiver K&M USB ports.
- If using audio de-embedding, connect headphones, a soundbar, speakers, or amplifier to the Receiver AUDIO OUT port.
- Connect the included DC 5V/2A power adapter to the Transmitter.
- Connect the included DC 5V/2A power adapter to the Receiver.
- Power on the HDMI source and displays.
- Confirm the POWER LEDs are on.
- Confirm the LINK LEDs are on.
- Confirm the Transmitter IN LED lights when HDMI source signal is detected.
- Confirm the OUT LED lights when a display is connected.
- Test video, local loop output, remote HDMI output, audio output, keyboard, and mouse control.
Fiber Cable Requirement — Critical
Use the correct fiber type for the required distance.
| Fiber Requirement | Specification |
| Single-mode fiber | Up to 10km |
| Multi-mode OM4 fiber | Up to 300m / 1000ft |
| Connector | LC |
| Fiber module | 10G SFP+ module |
Poor or incompatible fiber cable may cause:
- No video
- Flickering
- Black screen
- LINK LED not lighting
- Intermittent signal
- Audio dropouts
- USB keyboard/mouse not responding
- Remote display not detecting signal
For troubleshooting, test with a shorter fiber run, check LC connectors, confirm the cable type, and make sure the fiber cable is not damaged.
HDMI Cable Requirement — Critical
Use high-quality HDMI cables capable of 18Gbps transmission.
| HDMI Requirement | Specification |
| HDMI version | HDMI 2.0b |
| Video bandwidth | 18Gbps |
| Maximum video | 4K@60Hz 4:4:4 |
| HDCP | HDCP 2.2 |
Poor HDMI cables may cause:
- No picture
- Flickering
- Black screen
- Wrong resolution
- 4K60 failure
- HDR not working
- HDCP handshake issues
- Audio dropouts
- IN LED not lighting
- OUT LED not lighting
For troubleshooting, test the HDMI source directly with the display before using the extender.
USB Keyboard/Mouse Requirement — Critical
The USB ports support USB 1.1 HID keyboard and mouse only.
| USB Requirement | Support |
| Keyboard | Supported |
| Mouse | Supported |
| USB 1.1 HID devices | Supported |
| USB flash drive | Not supported |
| External hard drive | Not supported |
| Webcam | Not supported |
| Printer / scanner | Not supported |
If the keyboard or mouse does not work:
- Confirm the source PC is connected to the Transmitter USB HOST port.
- Use the included USB Type-A to Type-B cable.
- Confirm the keyboard and mouse are connected to the Receiver K&M ports.
- Test the keyboard and mouse directly with the computer.
- Avoid USB hubs during troubleshooting.
- Confirm the fiber LINK LED is on.
- Power cycle both units and the source computer.
Audio Requirement — Critical
The Receiver AUDIO OUT is for local audio output near the remote display.
| Audio Output | Requirement |
| HDMI OUT | Supports listed HDMI audio formats |
| AUDIO OUT | Use compatible stereo audio device |
| Recommended source format | PCM stereo for best analog output compatibility |
If there is no sound from AUDIO OUT:
- Check the 3.5mm audio cable.
- Confirm the connected headphones, soundbar, speaker, or amplifier is powered and set to the correct input.
- Confirm HDMI audio works through the display.
- Set the HDMI source audio to PCM stereo.
- Check whether the source is muted.
- Confirm the Receiver OUT LED and LINK LED are on.
EDID Requirement — Critical
The UHD-FO10-KVM uses automatic EDID management.
If both the local loop display and remote display are connected, the system uses the lower display capability to improve compatibility.
If there is no picture or the wrong resolution appears:
- Disconnect one display and test again.
- Try the remote display only.
- Try the local loop display only.
- Lower the source output resolution.
- Power cycle the source after changing display connections.
- Confirm both displays support the selected resolution.
Power Requirement — Critical
Both the Transmitter and Receiver require DC 5V/2A power.
| Power Detail | Specification |
| Power adapter input | AC 100–240V, 50/60Hz |
| Power adapter output | DC 5V/2A |
| Transmitter power consumption | 3.85W max |
| Receiver power consumption | 3.3W max |
| Power adapters included | 2 |
If either unit does not power on:
- Check the DC 5V power adapter.
- Confirm the outlet is working.
- Check whether the POWER LED is red.
- Try the other included power adapter.
- Power cycle both units.
Surge protection is recommended.
Firmware Update Port
Both the Transmitter and Receiver include a SERVICE port.
| SERVICE Port | Function |
| Transmitter SERVICE | Firmware update port |
| Receiver SERVICE | Firmware update port |
| Connector type | USB-C |
Use the SERVICE port only when instructed by OREI support or when a confirmed firmware update is provided.
Understanding the Application Example
The application example shows the Transmitter connected to a host computer and a local monitor. A single-mode fiber optic cable connects the Transmitter to the Receiver.
On the Receiver side, the HDMI OUT connects to a remote monitor, AUDIO OUT connects to 2.0 speakers, and the K&M USB ports connect to a keyboard and mouse.
This shows the main use case: an HDMI source can be extended up to 10km over fiber, while the local loop monitor remains connected at the Transmitter and the keyboard/mouse can control the host computer from the Receiver side.
Supported Technical Specifications
| Specification | Support |
| Product Type | 4K@60Hz HDMI Extender Loop - 10km Fiber-Optic with KVM |
| Model | UHD-FO10-KVM |
| HDMI Compliance | HDMI 2.0b |
| HDCP Compliance | HDCP 2.2 |
| Video Bandwidth | 18Gbps |
| Input / Output Video Resolutions | 4096x2160p60, 4096x2160p50, 3840x2160p60, 3840x2160p50, 3840x2160p30, 3840x2160p25, 1920x1200p60RB, 1920x1080p60, 1920x1080p50, 1360x768p60, 1280x800p60, 1280x720p60, 1280x720p50, 1024x768p60 |
| Color Space | RGB, YCbCr 4:4:4, YCbCr 4:2:2, YCbCr 4:2:0 |
| Color Depth | 8-bit, 10-bit, 12-bit |
| HDR | HDR10, HDR10+, Dolby Vision, HLG |
| Audio Formats | LPCM 2 / 5.1 / 7.1CH, Dolby Digital / Plus / EX, Dolby TrueHD, DTS, DTS-EX, DTS-96/24, DTS High Res, DTS-HD Master Audio, DSD |
| Fiber Optic | 10G SFP+ module |
| Transmission Distance | Up to 10km over single-mode fiber; up to 300m over multi-mode OM4 fiber |
| ESD Protection | IEC 61000-4-2: ±8kV air-gap discharge and ±4kV contact discharge |
| Transmitter Input | 1 x HDMI Type-A, 19-pin female |
| Transmitter Outputs | 1 x HDMI Type-A, 19-pin female; 1 x LC FIBER OUT |
| Transmitter Control Ports | 1 x USB Host Type-B; 1 x SERVICE USB-C |
| Receiver Input | 1 x LC FIBER IN |
| Receiver Outputs | 1 x HDMI Type-A, 19-pin female; 1 x 3.5mm stereo audio jack |
| Receiver Control Ports | 1 x SERVICE USB-C; 2 x USB Device Type-A |
| Housing | Metal enclosure |
| Color | Black |
| Dimensions | Transmitter / Receiver: 120mm x 78mm x 24.5mm / 4.72in x 3.07in x 0.96in |
| Weight | Transmitter: 260g / 9.17oz; Receiver: 256g / 9.03oz |
| Power Supply | DC 5V/2A |
| Power Adapter Input | AC 100–240V, 50/60Hz |
| Power Consumption | Transmitter: 3.85W max; Receiver: 3.3W max |
| Operating Temperature | 32°F to 104°F / 0°C to 40°C |
| Storage Temperature | -4°F to 140°F / -20°C to 60°C |
| Operating Humidity | 20%–80% RH, non-condensing |
| Storage Humidity | 10%–90% RH, non-condensing |
Package Contents
| Item | Quantity |
| UHD-FO10-KVM Transmitter | 1 |
| UHD-FO10-KVM Receiver | 1 |
| USB Cable Type-A to Type-B, 1.5m | 1 |
| Mounting Ear | 4 |
| Machine Screw | 8 |
| Power Adapter | 2 |
| User Manual | 1 |
What HDMI Source Devices Is the UHD-FO10-KVM Compatible With?
The UHD-FO10-KVM can connect to HDMI source devices such as:
- PCs
- Laptops
- Workstations
- Media players
- Streaming devices
- DVD players
- Blu-ray players
- Game consoles
- Cable boxes
- Satellite receivers
- HDMI matrix outputs
- HDMI switch outputs
- AV receiver HDMI outputs
The HDMI source must output a supported HDMI signal up to 4K@60Hz 4:4:4.
For KVM control, the source should be a computer or host device that accepts USB keyboard and mouse input.
What Displays Is the UHD-FO10-KVM Compatible With?
The UHD-FO10-KVM can connect to HDMI display devices such as:
- 4K TVs
- UHD monitors
- HDMI projectors
- Computer monitors
- Commercial displays
- Conference room displays
- Classroom displays
- Control room displays
- Security monitoring displays
- Digital signage displays
The connected display must support the selected HDMI resolution, HDR format, audio format, and HDCP requirements.
What USB Devices Are Supported?
The UHD-FO10-KVM supports USB 1.1 HID devices only.
Supported USB devices include:
- USB keyboard
- USB mouse
Unsupported USB devices include:
- USB flash drives
- External hard drives
- Printers
- Scanners
- Webcams
- USB audio devices
- USB hubs
- Other non-HID USB peripherals
Frequently Asked Questions
Q: What is the UHD-FO10-KVM used for?
A: It is used to extend HDMI video and USB keyboard/mouse control over fiber optic cable up to 10km.
Q: Is the UHD-FO10-KVM an HDMI over fiber extender?
A: Yes. It is a 4K@60Hz HDMI Extender with loop output over fiber optic cable.
Q: Does it support KVM?
A: Yes. It supports USB 1.1 keyboard and mouse transmission from the Receiver side.
Q: How far can it extend HDMI?
A: It supports up to 10km over single-mode fiber cable.
Q: Can I use multi-mode fiber?
A: Yes. Multi-mode OM4 fiber can be used, but the distance is reduced to 300m / 1000ft.
Q: What fiber connector does it use?
A: It uses LC fiber connectors.
Q: What fiber module does it use?
A: The manual lists a 10G SFP+ fiber optic module.
Q: Does it support 4K@60Hz?
A: Yes. It supports video resolutions up to 4K@60Hz 4:4:4.
Q: What HDMI version does it support?
A: It supports HDMI 2.0b.
Q: What HDCP version does it support?
A: It supports HDCP 2.2.
Q: What video bandwidth does it support?
A: It supports 18Gbps video bandwidth.
Q: Does it support HDR?
A: Yes. HDR10, HDR10+, Dolby Vision, and HLG are supported.
Q: Does it support 3D video?
A: Yes. 3D video is supported.
Q: Does the Transmitter have HDMI loop output?
A: Yes. The Transmitter has an HDMI OUT port for local monitoring.
Q: What is the HDMI loop output used for?
A: It allows a local display to be connected near the source while the same HDMI signal is extended to the remote Receiver.
Q: Does the Receiver have audio output?
A: Yes. The Receiver has a 3.5mm AUDIO OUT port.
Q: What can I connect to AUDIO OUT?
A: You can connect headphones, a soundbar, powered speakers, an amplifier, or another compatible audio device.
Q: What HDMI audio formats are supported?
A: LPCM 2 / 5.1 / 7.1CH, Dolby Digital / Plus / EX, Dolby TrueHD, DTS, DTS-EX, DTS-96/24, DTS High Res, DTS-HD Master Audio, and DSD are supported.
Q: Does it support USB devices other than keyboard and mouse?
A: No. It only supports USB 1.1 HID devices such as keyboard and mouse.
Q: Can I connect a USB flash drive?
A: No. USB storage devices are not supported.
Q: Can I connect a printer, scanner, or webcam?
A: No. These USB devices are not supported.
Q: How do I connect the keyboard and mouse?
A: Connect the source PC to the Transmitter USB HOST port using the included USB Type-A to Type-B cable, then connect the keyboard and mouse to the Receiver K&M ports.
Q: Does it support automatic EDID management?
A: Yes. If both the Transmitter loop output and Receiver output are connected to displays, the system uses the lower display capability for compatibility.
Q: What happens if only one display is connected?
A: The system uses that display’s EDID.
Q: Why is my source not outputting 4K?
A: If both displays are connected, the system may use the lower-capability display EDID. Disconnect the lower-resolution display or use only the 4K display for testing.
Q: What does the Transmitter POWER LED mean?
A: It lights red when the Transmitter is powered on.
Q: What does the Receiver POWER LED mean?
A: It lights red when the Receiver is powered on.
Q: What does the LINK LED mean?
A: It lights green when the Transmitter and Receiver have a normal optical fiber connection.
Q: What does the Transmitter IN LED mean?
A: It lights green when an HDMI source signal is detected on HDMI IN.
Q: What does the OUT LED mean?
A: It lights green when a display device is connected to the HDMI OUT port.
Q: What should I do if there is no video or the output flickers?
A: Check HDMI and fiber connections, use single-mode fiber, test with a shorter fiber run, try a lower source resolution, and check whether the Transmitter HDMI loop output has the same issue.
Q: What should I do if the LINK LED does not light?
A: Check the fiber cable, LC connectors, fiber type, SFP module connection, and make sure both units are powered.
Q: What should I do if the local HDMI loop output works but the remote display does not?
A: Check the fiber cable, Receiver power, Receiver HDMI cable, Receiver display input, and LINK LED.
Q: What should I do if the keyboard or mouse does not work?
A: Confirm the PC is connected to the Transmitter USB HOST port, confirm the keyboard/mouse are connected to the Receiver K&M ports, and test the keyboard/mouse directly with the PC.
Q: What should I do if audio does not work from AUDIO OUT?
A: Check the 3.5mm cable, confirm the audio device is powered and on the correct input, and set the HDMI source audio to PCM stereo.
Q: Does each unit need power?
A: Yes. The manual lists two included DC 5V/2A power adapters, one for the Transmitter and one for the Receiver.
Q: What power supply does it use?
A: It uses DC 5V/2A power adapters.
Q: What is the power consumption?
A: The Transmitter consumes up to 3.85W, and the Receiver consumes up to 3.3W.
Q: Does it have firmware update ports?
A: Yes. Both the Transmitter and Receiver have USB-C SERVICE ports for firmware updates.
Q: What is included in the package?
A: The package includes the Transmitter, Receiver, USB Type-A to Type-B cable, four mounting ears, eight machine screws, two power adapters, and one user manual.
Comments
0 comments
Please sign in to leave a comment.