Introduction
This troubleshooting guide helps you resolve common issues with the OREI EARC-201 1-in-2-out eARC Splitter. The EARC-201 is designed to take a TV's eARC HDMI output and split audio to two eARC or ARC soundbars at the same time. If you are experiencing audio loss, handshake problems, or control issues, the steps below can help you identify the cause and restore proper operation.
Issue description
The EARC-201 is intended for setups where one TV eARC HDMI output must feed two compatible soundbars simultaneously. Most issues reported by customers are related to device compatibility, TV audio settings, HDMI port selection, or CEC/eARC handshake behavior. Important: the EARC-201 only supports eARC/ARC soundbars on its outputs. Passive speakers, non-ARC devices, and standard speakers will not work directly on the splitter outputs.
Signs
One soundbar works, but the second output has no audio.
The eARC LED blinks or never establishes a stable eARC connection.
No audio is heard from one or both connected soundbars.
The TV does not seem to recognize both outputs correctly.
CEC power on/off commands do not work as expected.
Bluetooth audio on the TV disables eARC audio.
Basic troubleshooting steps
Before moving to advanced troubleshooting, try these basic checks first.
Confirm that both connected devices are eARC or ARC soundbars. Passive speakers and non-ARC devices are not supported on the EARC-201 outputs.
Verify that the TV is connected to the correct HDMI port labeled eARC or ARC.
Check the TV audio settings and make sure eARC is enabled.
Make sure HDMI cables are high-speed and securely connected to all ports.
Power cycle the TV, the EARC-201, and both soundbars by unplugging them for 30 seconds and reconnecting them.
If you are using TV Bluetooth, disable it and test eARC again. Using Bluetooth on the TV can mute or interrupt eARC audio.
If needed, test with one soundbar at a time to confirm whether the issue is with the splitter or one of the connected devices.
Advanced troubleshooting steps
1. One output is not working
If one soundbar works and the other does not, first confirm that the non-working device is an eARC or ARC soundbar. The EARC-201 does not support passive speakers, analog speakers, or non-ARC audio devices on either output. If the device is compatible, swap the two outputs and swap the HDMI cables to determine whether the problem follows the cable, the soundbar, or the splitter port.
If the same soundbar still does not work after swapping ports and cables, the issue is likely with that soundbar's settings or compatibility with the TV's audio format.
2. eARC LED is blinking or eARC is not establishing
A blinking eARC LED usually indicates a handshake issue between the TV and the splitter. To resolve this, turn off all devices, disconnect power for 30 seconds, and reconnect in this order: TV, EARC-201, then both soundbars. After rebooting, re-enable eARC in the TV audio settings.
If the issue continues, try a different HDMI cable between the TV and the EARC-201, and confirm the TV is using the correct HDMI port that supports eARC.
3. No audio from one or both outputs
No audio is often caused by an incompatible audio format or a TV setting issue. Confirm that the TV audio output is set to eARC or external audio system, and check whether the TV is sending a format supported by both soundbars. Some soundbars may not support every audio format, so test with a standard format if available.
Also verify that the TV app or source device is actually sending audio through the TV's eARC output and not through another output path.
4. CEC power control questions
The EARC-201 can pass CEC-related control behavior through compatible devices, but results depend on the TV and soundbar brands and their CEC implementation. Brand names for CEC may include Samsung Anynet+, LG SimpLink, and Sony Bravia Sync.
If power on/off commands are not working on both soundbars, enable CEC on the TV and on each soundbar, then power cycle all devices. Some TVs and soundbars may not support identical CEC behavior across multiple outputs, so full simultaneous control is not guaranteed in every setup.
5. Independent output control is not available
The EARC-201 outputs audio to both connected soundbars at the same time. It does not support selecting only Output 1 or only Output 2. If you need independent output selection, this splitter is not designed for that use case.
6. Passive or non-eARC speakers are not working
This is expected behavior. The EARC-201 is designed only for eARC/ARC soundbars on its outputs. Passive speakers, powered speakers without ARC/eARC support, and devices without HDMI ARC/eARC capability will not function directly from the splitter.
If you want to use passive speakers, you will need a separate audio solution that is designed for that type of speaker setup.
7. TV Bluetooth is muting eARC audio
On many TVs, enabling Bluetooth audio disables or interrupts eARC output. If you want to use Bluetooth audio and eARC audio at the same time, the TV's built-in Bluetooth may not support that configuration. In that case, use an independent Bluetooth transmitter instead of the TV's Bluetooth function.
Contact support
If you still need help after completing the steps above, contact OREI support for assistance.
Email: info@orei.com
Phone: +1 877-290-5530
Hours: 9 AM to 5 PM CST, Monday through Friday
Disclaimer
This guide is provided for general troubleshooting purposes only. Device compatibility, CEC behavior, audio format support, and eARC performance can vary by TV, soundbar, cable, and firmware version. OREI cannot guarantee that every combination of equipment will function identically. If you are unsure about compatibility or setup, please contact support before making changes to your system.
Comments
0 comments
Please sign in to leave a comment.