Introduction
This troubleshooting guide helps you resolve common issues with the OREI EARC-102 2-in-1-out eARC/ARC HDMI Switch. The EARC-102 is designed to connect one soundbar or AV receiver to two TVs, allowing you to switch manually or automatically between TV1 and TV2.
Issue description
Customers may experience problems such as no audio, eARC or ARC handshake failures, unexpected auto-switching, CEC control issues, or volume control not working. In some cases, users also want to prevent a soundbar from powering on when the TV turns on, or they want to know whether switching inputs fully isolates CEC and eARC signals.
Signs
- Soundbar turns on automatically when the TV powers on
- No audio from the soundbar or AV receiver
- eARC or ARC does not establish and the LED keeps blinking
- The switch changes inputs unexpectedly when both TVs are on
- TV remote volume control does not work
- CEC features such as Samsung Anynet+, LG SimpLink, or Sony Bravia Sync do not behave as expected
Basic troubleshooting steps
- Confirm that the soundbar or AV receiver is connected to the correct output on the EARC-102.
- Make sure the TV is connected to the TV eARC or ARC HDMI port, not a standard HDMI input.
- Enable eARC or ARC in the TV audio settings if your TV supports it.
- Check that HDMI-CEC is enabled on the TV if you want volume control and device control to work.
- If you want to stop CEC power commands, disable HDMI-CEC in the TV settings. This is the simplest way to prevent the soundbar from turning on with the TV.
- Test with a different HDMI cable if the handshake is unstable or the LED is blinking.
- Set the TV audio output format to a compatible option such as PCM or Auto, depending on your equipment.
- If both TVs are on, manually select the desired input to avoid unexpected auto-switching.
Advanced troubleshooting steps
1. Soundbar powers on automatically with the TV
If the soundbar powers on when the TV turns on, the TV is likely sending a CEC power command. Disable HDMI-CEC on the TV to stop the command from being sent. Brand names for HDMI-CEC may include Samsung Anynet+, LG SimpLink, or Sony Bravia Sync.
If you switch the EARC-102 to an empty or disconnected input, the active audio path moves away from the original TV input. However, this does not electrically isolate HDMI pins 13, 14, or 19. CEC and eARC or HEAC signals may still be present, so the soundbar may still receive CEC commands from the inactive TV.
2. CEC signal isolation question
Switching inputs on the EARC-102 does not completely isolate CEC and eARC signals from the inactive TV. The switch does not electrically disconnect HDMI pins 13, 14, or 19. If you need complete CEC isolation, disable HDMI-CEC on the TV itself.
3. eARC or ARC is not establishing
If the eARC or ARC handshake fails and the LED blinks, power off the TV, soundbar, and EARC-102. Disconnect all HDMI cables, then reconnect them securely. Power on the TV first, then the EARC-102, and finally the soundbar or AV receiver. Confirm that the TV is using the correct eARC or ARC port and that eARC or ARC is enabled in the TV menu.
If the issue continues, try another HDMI cable and verify that the TV firmware and soundbar firmware are up to date.
4. No audio from the soundbar
No audio is often caused by using the wrong TV HDMI port, leaving eARC or ARC disabled in the TV settings, or selecting an unsupported audio format. Make sure the TV is connected to the correct eARC or ARC port and that the TV audio output is set correctly.
If your TV supports it, test with PCM first to confirm audio output. Then try Auto or Bitstream if needed, based on your soundbar or receiver compatibility.
5. Auto-switching behavior
The EARC-102 can automatically switch to the active TV input. If both TVs are on at the same time, the switch may move to the most recently active source or the source detected by the unit. If this behavior is not desired, use manual switching instead.
To keep one TV active, manually select TV1 or TV2 using the button or remote control and avoid turning on both TVs at the same time when possible.
6. Manual vs. auto switching
Manual switching is supported if you want full control over which TV is active. Use the front-panel button or remote to select the desired input. If auto-switching is enabled and causes interruptions, switch to manual mode if available in your setup.
7. TV remote volume control is not working
If the TV remote no longer controls the soundbar volume, CEC may be disabled on the TV or the CEC link may not be passing correctly through the connected devices. Re-enable HDMI-CEC if you want volume control, or use the soundbar remote if CEC must remain off.
Contact support
If you still need help, contact OREI support and have the following details ready:
- Your EARC-102 model number and purchase details
- TV brand and model number
- Soundbar or AV receiver brand and model number
- Which HDMI ports are being used on the TV and soundbar
- A description of the issue and any troubleshooting steps already completed
- Any LED behavior, blinking patterns, or error messages you see
Support hours: 9 AM to 5 PM CST, Monday through Friday
Email: info@orei.com
Phone: +1 877-290-5530
Disclaimer
This guide is intended for general troubleshooting only. HDMI-CEC, eARC, and ARC behavior can vary by TV, soundbar, AV receiver, firmware version, and brand-specific settings such as Samsung Anynet+, LG SimpLink, and Sony Bravia Sync. If you are unsure about any step, or if your equipment continues to malfunction, please contact support for assistance before making additional changes.
Comments
0 comments
Please sign in to leave a comment.